The icon is a little different to what I’ve seen on others and I don’t know how to tell otherwise.

Thanks!

  • @SchmidtGenetics@lemmy.world
    link
    fedilink
    English
    11
    edit-2
    10 months ago

    The hammering most of these 1/2 drill “hammer drills” perform isn’t the same percussive hammering as real sds hammer drills though.

    Great for putting a hole in brick or mortar, but trying to go into actual concrete will be a lesson in futility.

    • @blackstratOPA
      link
      English
      4
      edit-2
      10 months ago

      I’ll be putting a hole all the way through breeze block. Would it be ok?

      Edit: km trying to avoid the expense of an SDS if I can as I only have 1 hole to do.

      • @glimse@lemmy.world
        link
        fedilink
        English
        710 months ago

        You’ll be ok.

        I’m assuming you’re using a masonry bit so I’m gonna give you another tip:

        LET THE BIT/DRILL COOL DOWN. You might burn the drill out and you WILL dull the bit. You don’t need to drill through in one shot…drill for 20-30 seconds and wait a few minutes. It’s slow but worth it.

        • @GluWu@lemm.ee
          link
          fedilink
          English
          310 months ago

          Masonry bits are carbide tipped and don’t dull, they just break. Heat is not an issue and the bit doesn’t even function by cutting. It’s a downward 45 angle in order to chip as it rotates. There’s no cutting force from the rotation.

          • @glimse@lemmy.world
            link
            fedilink
            English
            7
            edit-2
            10 months ago

            Good masonry bits are carbide-tipped but not all of them. I used those with our sls drill but I stuck to the cheaper ones for anything under 1/2"

            Perhaps dull was the wrong word but the tips do wear out. You wind up with a useless flat stub at the end that won’t push through anything

      • @SirSamuel@lemmy.world
        link
        fedilink
        English
        210 months ago

        You’ll be fine. I’ve found applying pressure for about ten seconds, then clearing the hole, rinse and repeat, works well when using a “hammer drill” like this. Use speed 2.

        Also, use a HEPA filter equipped vacuum to capture the dust as it’s created, and wear an N95 dust mask while drilling. Silicosis is no joke

    • @SirSamuel@lemmy.world
      link
      fedilink
      English
      110 months ago

      Eh, drilling small holes in concrete is fine. If I need to throw a quick tapcon or something in a slab I’ll just use my 1/2" chuck cordless hammer drill. You’re absolutely right about larger holes though. What a pain. And don’t talk to me about hitting rebar lol

        • @SirSamuel@lemmy.world
          link
          fedilink
          English
          110 months ago

          Interesting. Do you know any for comparison, off the top of your head? I use a Milwaukee cordless myself. In the past I’ve use DeWalt, but that was in the 14.4V days. I didn’t think there was any difference in 1/2" chuck hammer drills beyond battery size and motor., but I’d love to learn more

          TBH I’ve always bought drills with a hammer function simply because they have metal casings, are made of sturdier construction, and are less likely to burn out when I’m drilling in 100yr old oak doors

      • @SchmidtGenetics@lemmy.world
        link
        fedilink
        English
        2
        edit-2
        10 months ago

        Yes it’s possible, it’s just why spend 30 minutes drilling one hole when you could have the proper tool and be done in seconds.

        Homeowner doing it for themselves it makes sense, but if you’re paying someone or doing it to make money, get the right tools. You’ll make the money back in a dozen holes from the man hours you save.